MSRM WiFi extender setup

Are you looking for MSRM WiFi extender setup instructions? Having problems configuring the MSRM? Do you desire unlimited access to high-speed internet in your home or place of business, even in outlying locations? Don’t worry if you answered “yes” to any of these questions. You’ve come to the right place. This article contains detailed instructions for configuring an MSRM WiFi extender. Let’s start by getting everything ready.

Simple Instructions for MSRM WiFi Extender Setup

Sure, here are simple instructions for MSRM WiFi Extender setup:

1. Plug extender into an outlet.

2. Connect to “MSRM-Ext” network.

3. Open browser, enter ap.setup.

4. Log in (default: admin/admin).

5. Click “Wizard” or “Setup” option.

6. Scan for your WiFi network.

7. Select and enter WiFi password.

8. Click “Apply” or “Connect.”

9. Wait for extender to reboot.

10. Reconnect to extended network.

11. Setup complete! Enjoy better WiFi coverage.

You can reach our team of highly technical experts by calling +1-323-471-3045 or sending an email to support@mywifiextension.net. They are available to assist you whenever you need it.

MSRM WiFi extender setup Using WPS

For MSRM WiFi extender setup via WPS, follow the steps below:

• For MSRM WiFi extender setup, put the extender and router in the same space.
• Press the WPS button after the power LED light has stabilised. The LED light then begins to flash.
• The device’s WPS button becomes functional in two minutes. 
• Log into your device, go to the wireless settings, and turn on WPS if the WPS button is disabled.
• The WPS light on the router and extender will then flash for roughly 12 seconds.
• The router will shut off and the WPS repeater’s light will solidly turn green once the WPS has been set up.
• Finally, the extender will show up in the WiFi list as your network name.
• Place your extender halfway between the area and the router after unplugging it.

MSRM WiFi Extender firmware update

Here are simple instructions for updating the firmware on an MSRM WiFi Extender:

• Connect your computer or smartphone to the extender’s WiFi network.
• Open a web browser and enter the extender’s IP address (usually found in the user manual or on the extender itself).
• Log in to the extender’s web-based interface using your admin credentials (usually admin/admin by default).
• Look for a “Firmware Update” or “Upgrade” option in the settings menu.
• Download the latest firmware from the official MSRM website and upload it through the extender’s interface.
• Wait for the update to complete, and the extender may reboot automatically.
• The firmware is now updated, enhancing performance and security.

MSRM WiFi Extender Factory Reset 

The following straightforward guidelines can be used to perform a factory reset on an MSRM WiFi Extender:

• Find the extender’s reset button, which is typically a tiny hole.
• With the extender turned on, press and hold the reset button with a paperclip or pin for approximately 10 seconds.
• When the extender restarts or the LEDs begin to flash, release the reset button.
• Hold off until the extender has finished the reset procedure, which could take a while.
• All customised configurations will be erased and the extender will revert to its default settings.
• The extender can now be modified as necessary.

Be prepared to reconfigure the device because a factory reset will remove all of your custom settings, including network names and passwords.

MSRM wifi extender modes

The MSRM wifi extender typically has three modes:

1. Repeater mode: To extend wireless coverage to potential out-of-range areas, the extender receives the router’s current wifi signal and retransmits it. 

2. Access point mode: In this mode, the extender connects to the current router using an Ethernet cable to establish a new wifi network. The extender can then be directly connected by the device that needs to connect to the wifi network.

3. Router Mode:In this mode, a secure wireless network is created. It makes it possible for numerous devices to connect to the network simultaneously. This mode converts the extender into a router if you have a modem but no router.

You can contact our team of highly technical experts who are available to assist you whenever you need it by calling +1-323-471-3045 or sending an email to support@mywifiextension.net.